Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - mjessy

Pages: [1] 2 3 ... 7
1
General Discussion / Activation
« on: December 28, 2013, 04:32:24 pm »
As usual I have major issue trying to activate this PITA program.
For everything I do there is an error message.
I cannot use either of my purchase codes , god knows why they exist as in normal programs all you need is a purchase code.
Instead we have to face this crap of pre reg info which never seems to work. I am sick to the teeth of this constant issue and worry every time there is a change.
Brahim can you do ANYTHING about these constant registration and licence issues and sort it so that we only need a purchase code like all other programs out there?
In the meantime can you assist with my issue cos I am about to give up on Flexraid?
I cannot activate the program after changing my OS in any way or form, I have tried all the ways and keep getting error 500 or code not exists.

2
General Discussion / Re: Drives missing
« on: May 31, 2012, 06:24:03 pm »
yes i am using a raid card but not with green drives. i will check to see if the drives have an idle mode. If it has, maybe when i restart the flexraid service it wakes it up. Thanks for info.

3
General Discussion / Re: Drives missing
« on: May 31, 2012, 02:38:11 am »
yeah in the drive manager. Once I stop and restart the service its ok again. It happens at different times with different drives.

4
General Discussion / Drives missing
« on: May 30, 2012, 07:25:34 pm »
Brahim, I have had some drives showing up as missing after a while and every now and again and when I stop and restart the flexRaid service the drive that was missing then shows up as healthy. Do you have any idea why this could be happening?

5
General Discussion / Re: Screenshots requested
« on: May 30, 2012, 01:58:23 am »
Sweet setup, what's the model# for the case?

Thanks, The Model of case is Antec 1200 V3.

6
General Discussion / FlexRAID in Auto Space-Priority
« on: May 29, 2012, 02:28:44 pm »
I have noticed after using FlexRAID in auto folder mode merge that all the data from one folder is spread across several hard drives, this is a pain to reconfigure again if necessary. I was wondering has anyone used the Auto Space-Priority mode, if so does this stop folder splits and keep all your files in one folder as they were before using auto folder mode? I would like to try this as Auto folder mode is a real pain if it continually seperates your files across drives.

7
I Believe you would need Brahim to sort this one out for you. Maybe you should pm him.

8
Yeah I didn't realize that about the board and CPU change, which is what i had. i changed the board and CPU with another machine in the house due to controller card problems and i kept trying to activate with the purchase code. Once i saw the info from Brahim and cg2101 I slowly figured it out but I must admit it was frustrating. Thanks for your help.

9
have tried everything with no luck. All this time unprotected!!! NOT GOOD

10
after re installing my OS AGAIN due to issues, I am unable to activate my flexRaid software. I am getting registration failure message and invalid request message. This is a pain as it now leaves me unprotected. Can you advise?

11
Snapshot RAID / Re: Parity creation
« on: May 17, 2012, 05:04:47 am »
That link does not explain URU.

12
General Discussion / Re: Adding Additional PPU in CC Mode
« on: April 27, 2012, 11:04:48 am »
Brahim can you confirm whether or not  its possible to add additional PPU to existing Set up in CC mode as i have tried everything on wiki and forum and also what you have suggested with no luck?

13
General Discussion / Re: Adding Additional PPU in CC Mode
« on: April 27, 2012, 09:26:01 am »
Thats ok, I guess for now the only way is to delete config, wipe current PPU's clean and rebuild with the third PPU added from scratch.

14
General Discussion / Re: Adding Additional PPU in CC Mode
« on: April 27, 2012, 09:17:28 am »
that wiki is only for increasing size not adding an additional PPU. Maybe Brahim will add a procedure for adding additional PPU in CC mode.

15
General Discussion / Re: Adding Additional PPU in CC Mode
« on: April 27, 2012, 09:13:42 am »
ok i will read it and see if i can follow procedure and let you know, thanks for info.

Pages: [1] 2 3 ... 7